- 1
- Piece/Pieces
Basic Data you will require
The type of material being fed, the angle of repose and weight per cubic foot (kg/ m.cu). A rough calculation of the material sizes. The greatest dimension of the biggest piece. Needed feeder conveying distance. Ideal feeder capacity.
STEP 1: With the help of computed precision of big size materials, ideal width of the feeder is selected from Table A. Multiply this factor by the greatest dimension of the material's largest piece to determine minimal width of feeder width. There is also a throat opening factors where the use of a four-sided hopper is done. To find the minimal hopper throat opening proper factors are selected and multiplied by the same largest dimension.
STEP 2: Determine the different combinations of feeder slopes and widths available for the needed capacity. Neglect any which are tinier in width than the minimum feeder width calculated before. It may become necessary to enhance the minimum width of the feeder in order to gain the desired capacity. If so, ignore minimum width from previous step and substitute with the altered minimum feeder width for the needed capacity.
STEP 3: Now regard feeder length. Generally the positioning and size of companion equipment like conveyors, crushers, hoppers, aprons, chutes, etc. propose the given to minimized length of the feeder pan. Also, the pan could not be shorter than that which is required to hold the material at its repose angle on the pan after the shutting down of the feeder. Find out minimum pan lengthen make your own scaled diagram to demonstrate the angle of repose and slope of feeder on the rest and pan. Enable the throat opening of the proper hopper when utilizing a hopper with four sides. Add 12" (30 cm) to the length of the pan as a factor of safety to forestall the material from continuing to freely flowing. After this, add the length of any grizzly sections which is needed to the minimum pan length to ascertain the minimum feeder length.
STEP 4: Again evaluate slopes, width and capacities. Regard headroom and feeder length needs. Match these with location, critical dimensions and elevations of associated equipment. Recollect to allow for future demand of increase in capacity. Now select the slope/ width combination which matches the desired capacity and which is ideal for the particular installation and application. You would need to go steeper and narrower to match up with a crusher opening; possibly wider to have feed from an active apron conveyor. Or, you may need to go wider with comparatively less slopes to suit the limits of elevation. You are possibly to discover that although over one size feeder will fulfill your capacity needs, one specific width/ length/ slope combination optimally serves your predefined needs.
The straight-line motion by VGF Series and grizzly feeders are for regulated feeding of primary crushers after screening.
VGC Series Primary vibrating feeders mix run-of-quarry scalping and feeding oversize retained by grizzly bars to crusher. Fines passing the bars of steel spacing such as crusher jaw setting, could be directly sent to screening.
Advantages of Grizzly Feeder:
Max. capacity working of the Crusher with low depreciation since the chamber for crushing is not filled with materials of undersize.
Grizzly fines, released by belt conveyor, crushed prod, safeguard the rubber belt from shearing and attrition owing to the discharge of product from primary crusher.
Table A-Section Factors
Percentage Large Size* | Feeder with Factor | Hopper throat Factor |
1-10% | 1.3 | 1.5 |
10-40% | 1.5 | 2 |
40-60% | 2 | 2.5 |
60-90% | 2.5 | 3 |
90-100% | 3 | 3.5 |
*Those pieces which have a size range of 75 to 100% of the greatest piece. If the largest piece is 91cm (36") then "largesize" are all pieces 69 cm (27") and larger.
Capabilities founded on material weighing 1600 kg/m.cu. (100 Ib./ft.cu), 30 cm(12") material bed depth and 13 mm (1/2") stroke at the rate of 800 RPM.
Slope of Pan | Feeder Width in mm/tons per House | ||||||||
800 | 900 | 1100 | 1200 | 1400 | 1500 | 1800 | 2000 | 2500 | |
0 DEG | 275 | 350 | 400 | 475 | 525 | 600 | 725 | 850 | 1000 |
5 DEG | 375 | 450 | 525 | 600 | 675 | 750 | 900 | 1050 | 1160 |
10 DEG | 450 | 550 | 650 | 725 | 825 | 900 | 1075 | 1250 | 1440 |
15DEG | 550 | 650 | 750 | 850 | 975 | 1075 | 1300 | 1500 | 1850 |
Size | VGF 800 | VGF 900 | VGF 1100 | VGF 1200 | VGF 1400 | VGF 1500 | VGF 1800 | VGF 2000 | VGF 2500 |
Size of | 800 | 900 | 1100 | 1200 | 1400 | 1500 | 1800 | 2000 | 2500 |
feed | | | | | | | | | |
deck | | | | | | | | | |
width | | | | | | | | | |
Grizzly | 1600 | 1700 | 1800 | 2000 | 2400 | 2500 | 2600 | 3000 | 3200 |
length | | | | | | | | | |
Total | 2800 | 3000 | 3300 | 3600 | 4200 | 4400 | 4600 | 5600 | 6600 |
length | | | | | | | | | |
Grizzly | 50/ | 50/ | 50/ | 507 | 507 | 507 | 507 | 507 | 507 |
bars- | 150 | 180 | 200 | 200 | 250 | 250 | 300 | 350 | 400 |
openings | | | | | | | | | |
Max. feed | 500 | 600 | 700 | 800 | 1000 | 1100 | 1200 | 1400 | 1600 |
size mm | | | | | | | | | |
Max. | 250 | 350 | 400 | 480 | 640 | 750 | 1040 | 1200 | 1400 |
capacity | | | | | | | | | |
TPH | | | | | | | | | |
Horse | 15 | 20 | 25 | 30 | 30 | 40 | 50 | 75 | 100 |
power | | | | | | | | | |
Wt. | 3500 | 4200 | 5200 | 6500 | 8800 | 9800 | 12200 | 14600 | 16200 |
Kgs. | | | | | | | | | |
Features of Grizzly Feeder:
- Large welded frame to tolerate high shock loads.
- Transportation deck with grizzly and pan combination, back and side renewable liners.
- Stepped grizzly and non-plugging, singly renewable, for easy fines passing and material tilting.
- Vibrating unit comprises two counter-rotating eccentric shafts, geared jointly in oil-bath. Special roller bearings protected by grease labyrinths and in oil-bath.
- Varying imbalance of the machine effects the setting of amplitude.
- Actuation is by V-belts drive and 4-pole motor.
- Special steel springs ordered for the installation on steel supporting structure or concrete.
- Welded plate supporting structure (supplied on request), steel-sections preset and cross-breams for fines and feed discharge hopper application. It is possible to insert a device for uninterrupted output setting.
Mode | A | B | C | D | E | F | G |
VGF 800 | 2800 | 800 | 1950 | 535 | 730 | 1290 | 1180 |
VGF 900 | 3000 | 900 | 2200 | 560 | 780 | 1350 | 1300 |
VGF 1000 | 3300 | 1100 | 2400 | 590 | 800 | 1400 | 1450 |
VGF 1200 | 3600 | 1200 | 2510 | 590 | 875 | 1460 | 1620 |
VGF 1400 | 4200 | 1400 | 2935 | 675 | 1000 | 1640 | 1800 |
VGF 1500 | 4400 | 1500 | 3100 | 700 | 1020 | 1720 | 2100 |
VGF 1800 | 4600 | 1800 | 3180 | 790 | 1190 | 1880 | 2275 |
VGF 2000 | 5600 | 2000 | 3500 | 900 | 1200 | 2000 | 2400 |
VGF 2500 | 6600 | 2500 | 4100 | 1100 | 1500 | 2200 | 2600 |
- Mumbai, Mundra
- Letter of Credit (L/C), Cheque, Cash in Advance (CID), Cash Advance (CA)
- Depend On Order Per Month
- Depends Upon Product Months
- Customized Packing
- Africa, Middle East, Western Europe, Eastern Europe, South America, North America, Central America, Australia, Asia
- All India
- ISO
Factory:- 906/4, GIDC, Near Kiran Motors, Makarpura Vadodara Gujarat India +918037400104
Phone :+918037400104